Eaton Cutler-Hammer
Eaton Cutler-Hammer Drives
Eaton Cutler-Hammer PLC
Eaton Cutler-Hammer Circuit Breakers
Allen Bradley Panelview
Allen Bradley PLC
GE Fanuc
Urgent Automation is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.
Product comes with Urgent Automation's 1-year warranty.
Rockwell Disclaimer: The product is used surplus. Urgent Automation is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Urgent Automation is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, Urgent Automation makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Urgent Automation also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Urgent Automation also makes no representations as to your right to install any such firmware on the product. Urgent Automation will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Urgent Automation is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.
Product comes with Urgent Automation's 1-year warranty.
The Eaton (Cutler-Hammer) FDC3015 is a thermal-magnetic circuit breaker from the C Series. This device can work with voltages of 600 Volts AC or 250 Volts DC. Its tripping value cannot be readjusted because this is a circuit breaker with non-interchangeable trip units. The current rating of the module is 15 Amps. If higher currents than this are flowing through the device, it will cut off the current flow (mechanically). This device has terminals only on the load side. The FDC3015 molded case circuit breaker is engineered to provide years of almost maintenance-free protection for electrical circuits. It is appropriate for protecting motors and drives and for applications that require high current switching capabilities. It is a cost-effective protective solution against ground fault conditions and short-circuits.
The Cutler-Hammer FDC3015 provides a fast reaction to short-circuits. To do this, the device uses an electromagnet that has a winding that is in the same series as the load current. When an excessive current flows through the circuit (and through the electromagnet) it causes the magnetic field to increase rapidly and to mechanically open contacts for current conduction. The item weight is approximated at 1.95 kilograms (4.3 pounds). Mounting hardware and unmounted terminations for this circuit breaker are sold and delivered in separate packages. There are 2 elements that can make the device go into the trip position – thermal and magnetic trip units. Users must perform the resetting of the device to put it back into operation after it trips. Note that if there was a thermal trip, the FDC3015 circuit breaker cannot be reset unless the thermal element has properly cooled.
| Part Number/Catalog No. | FDC3015 |
| Product Type | Molded Case Circuit Breaker |
| Series | C |
| Frame | F |
| Pole(s) | 3 |
| Trip Amps | 200 kA at 240 Volts |
| Interrupting Capacity | 4.5 pounds |
| Weight | Thermal-Magnetic |
| Trip Unit | 4.13 x 6 x 3.38 inches |
| Part Number/Catalog No. | FDC3015 |
| Product Type | Molded Case Circuit Breaker |
| Series | C |
| Frame | F |
| Pole(s) | 3 |
| Trip Amps | 200 kA at 240 Volts |
| Interrupting Capacity | 4.5 pounds |
| Weight | Thermal-Magnetic |
| Trip Unit | 4.13 x 6 x 3.38 inches |