Eaton Cutler-Hammer
Eaton Cutler-Hammer Drives
Eaton Cutler-Hammer PLC
Eaton Cutler-Hammer Circuit Breakers
Allen Bradley Panelview
Allen Bradley PLC
GE Fanuc
Urgent Automation is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.
Product comes with Urgent Automation's 1-year warranty.
Rockwell Disclaimer: The product is used surplus. Urgent Automation is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Urgent Automation is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, Urgent Automation makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Urgent Automation also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Urgent Automation also makes no representations as to your right to install any such firmware on the product. Urgent Automation will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Urgent Automation is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.
Product comes with Urgent Automation's 1-year warranty.
The Eaton FDC2175 is a complete molded case circuit breaker. This module belongs to the FDC Thermal-Magnetic Circuit Breakers Class with non-interchangeable trip units produced by the Eaton Corporation, formerly known as Cutler-Hammer. The FDC2175 is used to cut off the electric supply when an excessive current is detected. The device has 2 poles, and it is applicable to systems connected to 600 Volts AC (50 to 60 Hertz) or to 250 Volts DC voltage sources. The current rating of the FDC2175 is 175 Amps. When users purchase the device, they should check the completeness of the MCCB before installing it. Do not install the device if there is any visible damage to the module. The thermal protection feature of the device will respond to the heat emerging with currents that are higher than the current limit of the device.
The thermal trip occurs with a time delay in response to overloading. This is for the purpose of filtering the short-term current peaks which can normally occur with some types of equipment. When there is a short circuit or a ground fault, the magnetic protection trips instantaneously. The Eaton Cutler-Hammer FDC2175 circuit breaker supports reverse feed usage. It has a highly-isolated plastic housing. The weight of the MCCB is 2 pounds (0.91 kilograms). The module is UL listed and it satisfies the (P1) requirements of the International Electrotechnical Commission Recommendation 157-1 standards. This F-Frame sized circuit breaker is factory-sealed. Its installation procedure consists of connecting and torqueing the line and load terminals. Before that, the circuit breaker should be attached to the mounting panel over the pre-drilled holes.
| Part Number/Catalog No. | FDC2175 |
| Product Type | Molded Case Circuit Breaker |
| Series | C |
| Frame | F |
| Pole(s) | 2 |
| Trip Amps | 200 kA at 240 Volts |
| Interrupting Capacity | 3 pounds |
| Weight | Thermal-Magnetic |
| Trip Unit | 2.75 x 6 x 3.38 inches |
| Part Number/Catalog No. | FDC2175 |
| Product Type | Molded Case Circuit Breaker |
| Series | C |
| Frame | F |
| Pole(s) | 2 |
| Trip Amps | 200 kA at 240 Volts |
| Interrupting Capacity | 3 pounds |
| Weight | Thermal-Magnetic |
| Trip Unit | 2.75 x 6 x 3.38 inches |